Call

 

What're your thoughts and feelings on Tools You Need to Install a New Bathtub ?

Setting up a bathtub isn't exactly brain surgery, however it does need solid plumbing, woodworking, as well as in some cases, tiling skills. Changing an old bathtub with a brand-new one is likewise a moderately tough project. If the old bathtub is easily accessible, the job can relocate immediately; if you have to open a wall surface to eliminate the old bathtub as well as position the brand-new bathtub, the task is a lot harder. In either situation, the task is within a home handyman's abilities, although you will need an assistant to move out the old bathtub as well as set in the brand-new one. Make sure you have actually certified on your own for the job and are comfortable trying it. As opposed to hiring a service provider to take control of a halfway-completed task, it is far better to consider employing one prior to you start. Opportunities are you might require an expert plumber to make tube connections.
This short article will help you mount a brand-new tub in your restroom if you have currently purchased a new tub and do not need to transform the arrangement of your previous water system pipelines.
Your tools and material list ought to comprise the following:

 

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Tape Measure


• Pipe Caps


 

Getting ready for the Installation

First of all, the supporting framework provided with the bathroom ought to be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is very important to see to it that if the tap includes a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bath, it is likewise practical to fit a sustaining plate under the taps system to avoid strain on the bathtub.
Fit the flexible faucet adapters to the bottom of both taps using 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bathroom. Utilize the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. See to it you use all of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be fitted in its last position.

 

 

Removing Old Touches

If you require to change old taps with brand-new ones as a part of your installment, then the first thing you need to do is detach the water. After doing so, activate the faucets to drain pipes any kind of water remaining in the system. The procedure of getting rid of the existing faucets can be rather troublesome due to the limited accessibility that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a cloth ready for the staying water that will come from the pipes. When the supply pipes have been gotten rid of, make use of the very same tool to loosen the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from transforming during this process. When the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any kind of old securing compound.
Before going on to fit the new faucets, compare the pipeline links on the old faucets to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.

 

 

Mounting the Bathtub

Using the two wood boards under its feet, put the tub in the needed placement. The wood boards are valuable in equally spreading the weight of the bathtub over the location of the boards rather than concentrating all the weight onto 4 tiny factors.
The next goal is to ensure that the tub is leveled all round. This can be accomplished by checking the level as well as adjusting the feet on the bath tub up until the level reads level.
To install faucets, fit all-time low of the outermost versatile tap port to the ideal supply pipeline by making a compression join; then do the very same for the other tap.
Switch on the supply of water as well as examine all joints and new pipework for leaks and tighten them if necessary. Fill up the tub and also examine the overflow outlet and also the typical outlet for leakages.
Finally, take care of the bathroom paneling as described in the supplier's user's manual. Tiling and also securing around the tub must wait up until the tub has been made use of at the very least when as this will settle it right into its last placement.

 

 

Suitable New Taps

If the tails of the new taps are plastic, after that you will certainly need a plastic connector to stop damage to the string. One end of the adapter fits on the plastic tail of the tap and the various other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly need minimizing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the mounting hole in the bath/basin guaranteeing that the washing machines are in area between the tap as well as the sink. Safeguard the faucet in place with the supplier provided backnut. When the tap is safely in position, the supply pipes can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular faucet connectors. The former kind should be connected to the faucet ends first, tightening just by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.

 

 

Tiling Around the Bathtub

In the area where the bath fulfills the tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the installation can move sufficient to break a stiff seal, causing the water to penetrate the wall surface in between the bath and also the tiling, leading to difficulties with moisture and also feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your fixtures and also fittings. They are offered in tubes and cartridges, as well as can sealing spaces up to a size of 3mm (1/8 inch). If you have a larger void to load, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly fill the bath tub with water prior to securing, to enable the activity experienced when the bathtub is in use. The sealer can fracture rather very early if you do not take into account this activity before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily offered on the market. It is a good idea to fit the tiles utilizing water-resistant or waterproof sticky as well as grout.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

Hopefully you liked our topic about Tools You Need to Install a New Bathtub . Thanks a lot for taking a few minutes to browse our blog. For those who enjoyed reading our post please do not forget to share it. Thank-you for taking the time to read it.

Book Now!